Contech-lighting CGF8 User Manual download pdf

For Con-Tech Lighting Ceramic Metal Halide and Compact Fluorescent Decorative Stemlight Pendant Series:

CGM8, CGF8, CGM12 and CGF12

www.con-techlighting.com

All speciﬁcations subject to change without notice.

1-847-559-5500 This document can be recycled.

DECOSTMLT INST

Continued on Page 2

INSTALLATION PROCEDURES

FC MOUNT: Flexible Cable Mono-Point, Damp Location Listed

RS MOUNT: Rigid Stem Mono-Point, Damp Location Listed

Prior to assembly, ensure 4" Round or Square (with a Round-to-Square Junction Box

Cover Plate) Junction Box is properly mounted to the ceiling structure. The center-to-

center mounting holes on the 4" Round Junction Box are 3-1/2"; the Round-to-Square

Junction Box Cover are 2-3/4". Both use 8-32 x 1/2" screws.

Loosen the (2) Philips screws that hold the mounting bar to the top round wiring

compartment. (Figure 1) Attach the mounting bar to the junction box or junction box

cover. Continue with ﬁxture assembly instructions.

FIXTURE ASSEMBLY INSTRUCTIONS:

Shade/hood assembly comes with 132" of socket lead wiring in a silicone sleeve:

8" and 12" Single Lamp CFL Housings: (2) Blue, (2) Red, (1) Green

12" Two-Lamp CFL Housings: (2) Blue, (2) Red, (2) Yellow, (1) Green

8" and 12" CMH Housings: (1) Black, (1) White, (1) Green;

Black = Blue and White = Red

Bicycle Cable (CGF8 and CGF12):

The Bicycle Cable Connector has (1) 2mm recessed hex head screw for locking into

the nipple plus (2) 2mm recessed hex head screws for locking into the bicycle

cable. (Figure 2) (1) 2mm hex key wrench is supplied with each ﬁxture.

Determine length of bicycle cable required.

If cutting is required, loosen bicycle cable from connector. Slide bicycle cable off

the wiring. Remove wire grommet. Cut bicycle cable with a hacksaw using a ﬁne

tooth (32T) blade, BX Armor cable cutter or high speed metal cutting blade.

Remove any sharp edges. Re-insert internal wire grommet. Slide bicycle cable over

the wiring. NOTE: The bicycle cable will only accept the wires less the silicone

sleeve. Re-insert the bicycle cable connector. Tighten all hex head screws as

much as possible.

Flexible Cord (CGM8 and CGM12):

Determine the length of ﬂexible cord required.

If cutting is required, loosen the coiled 18-3 cable. There should not be any

excess cable in the ballast compartment. Leave only 6-8" for wiring available.

Mark the cable where it needs to be cut. Carefully score the outer jacket around the

diameter of the cable about 6-8" below the total length. Then, score the outer jacket

lengthwise for that 6-8" section. Use proper rotary cable slitters such as Ideal

#45-128 or Eclipse #200-009. Remove the outer jacket. Trim off the individual wire

insulations by 1/2".

For CMH ballast wiring, mark the white wire with red colored tape and the black wire

with blue colored tape. Insert the cut wiring through the cable connector on the ballast

housing. Attach the black strain relief bracket to cord. (Figure 5) Tighten the (2) plastic

straight blade screws in order to hold the cord to the ballast housing safely. (Figure 4)

Make your wiring connections to the CMH ballast inside the ballast compartment.

Rigid Stem (CGF8 and CGF12):

Determine length of the stem with internal coupling required. A swivel stem

attachment (35° adjustment) is included for sloped ceiling applications (Figure 2).

Assemble stems onto the shade/hood assembly one at a time, carefully feeding

wiring through each section.

After all the stems are attached completely, remove the (4) brass screws from the

top of the ballast compartment and insert the wiring into the bottom of the compart-

ment. (Figure 1) Screw the stem(s) into the nipple. Tighten all hex head screws

as much as possible.

Rigid Stem (CGM8 and CGM12):

Determine the length of the stem with external couplings required.

Loosen the (2) 3.0mm steel hex head screws from the cord grip connector. (Figure 3)

Remove the inner grommet. Slide the stems over the ﬂexible cord. Screw into the top

cable connector. Tighten the (2) 3.0mm steel hex head screws. Add couplings to the

stem (if required).

Determine the length of ﬂexible cord required.

Use the CGM (8, 12) Flexible Cord Instructions for the balance of the installation.

Loosen the (2) plastic straight blade screws from the ballast compartment cord grip

connector. (Figure 4) Remove the inner grommet. Insert the ﬂexible cord through

the connector. Screw the stem to the ballast compartment cable connector. Tighten

the (2) plastic straight blade screws.

Mono-Point Canopy: Metal Halide Installation

Metal Halide Installation

Bicycle Cable

Connector

Swivel Stem

Attachment

2mm Hex Head

Screw Locks

Onto Nipple

(2) 2mm Hex Head Screws

Lock Onto Bicycle Cable

Top of Canopy

Brass Screws

on Ballast Plate

Mounting Bar

12" Metal Halide

Decorative Stemlight

Cord Grip

Connector

18-3 Cable

Cord Grip Connector

There should not be any excess cable in the ballast

compartment. Leave only 6-8" for wiring available.

CFL Connectors

(2) Plastic Straight Blade Screws

(2) 3mm Hex

Head Screws

1 2

Summary of Contents

Page 1 - CFL Connectors

For Con-Tech Lighting Ceramic Metal Halide and Compact Fluorescent Decorative Stemlight Pendant Series: CGM8, CGF8, CGM12 and CGF12www.con-techlightin

Page 2

For Con-Tech Lighting Ceramic Metal Halide and Compact Fluorescent Decorative Stemlight Pendant Series: CGM8, CGF8, CGM12 and CGF12www.con-techlightin

Related models: CGF12 | CGM8 | CGM12 |

Comments to this Manuals

No comments

Contech-lighting CGF8 User Manual

Browse online or download User Manual for For the car Contech-lighting CGF8. ConTech Lighting CGF8 User Manual

Summary of Contents

Related models: CGF12 | CGM8 | CGM12 |

Comments to this Manuals

Related products and manuals for For the car Contech-lighting CGF8